OG-170EPE生产设备报价单

OG-170EPE生产设备报价单

一、价目表  price chart

报价：万元（FOB重庆）

型号：OG-PE170   model : OG-PE170

二、目录 (content)

1、主要设备清单(List of maior equipments)

2、主要设计数据(Data of main design)

3、公用工程要求(Demands of public project)

4、各单元规格(specifications of each part)

5、备件清单(List of spare parts)

1.主要设备清单(List of major equipments)

A.钢结构架 (steel rack structure)                   1套 (1set)

B.自动加料单元(auto feeding unit)                 1套 (1set)

C.挤出单元 (squeezing unit )                      1套 (1set)

D.发泡剂注入单元 (foamer-injecting unit)           1套 (1set)

E.抗缩剂注入单元 (anti-contractor-injecting unit )     1套 (1set)

F.发泡模头单元 (foaming mold-head unit )           1套 (1set)9

H.风环和定型鼓单元 (air ring & molding drum unit )   1套 (1set)

I.展平单元 (expanding unit )                       1套(1set）

J.牵引单元 (haul-off unit )                         1套(1set）

K.卷取单元 (rolling  unit )                        1套(1set）

L.成核剂注入单元及粉料拌料单元（adding rucleonizer、powder material mixing unit）                                       1套(1set）

2.主要设计数据 (major design data)

*应用树脂: (resin applied )         LDEPE

*挤出机能力:  (capacity of squeezing engine)   大约350-480KG/HR (about 350-450kg/hr)       (生产3mm-5mm片材时产量相对较低)

(yield would be relatively low when producing 3mm -5mm sheet)

*片材厚度: (thickness of sheet)  大约2~12mm(about 2-12mm)视片材密度厚度不同

*片材宽度: 1000-1650MM可调

(width of sheet )   (,depending on thickness of sheet)

*生产线速度: (speed of manufacture line)     10--80M/MIN

*电源规格:     3相X380V×50HZ   specifications of power :three phrases

3.公用工程要求( Demands of Public Project )

*电功率: (electric power) 约198KW(about 198kw)  

*冷却水: (cooling water )  300升/时 (300L/Hr)

*丁烷泵: (butane gas)      200L/ (200L/min)

*油脂泵:                20L/MIN (20L/min)

4.各单机规格(specifications of each  single part)

A.钢结构架 (steel rack structure )       1套 (1set)

 a)  配料操作台:     SS41钢制

operation table of blending materials :ss41 made of steel

 b)  钢扶梯:         SS41钢制

   steel ladder : ss41 made of steel

B.自动加料单元 (auto feeding unit )       1套 ( 1 set)

        a) 能力:    (capacity )         800公斤/小时 (800kg/hr)

        b) 加料方式: (feeding method )     自动喂料( auto feed)

        c) 料斗:  (measure implement)    不锈钢材质

        e) 驱动马达: (driving motor)         2HP ×4P×1套 ( set )

C.挤出单元 (squeezing unit)       1套( 1 set)

        a)  减速箱(deceleration box)

           --型式：(model  )   375硬质齿轮 (helical gear without pole)

          --材质：(material )   FCD25（可锻铸铁）(forgeable lion)

          --箱体：(box body)  FC20 硬质齿面   型号375          --齿轮：(gear wheel) SCM4（特殊齿形磨光和加热处理）

special gear wheel bolishing and heating dealing

          --马达：(motor )     AC160KW    配160KW变频器

        b) 颈部 (neck )

          --型式：(model)    水冷夹套( cooling water set)

          --材质：(material )  （锻铸件）( able to forge steel)

        c) 螺筒  (spiral tube )

--直径：(diameter )     ∮170×∮250mm

--材质：(material)     38铬目合金钢,经氮化处理HRC55-58(nitrogenized and chromium-plated HRC55-58)

 --加热区：(heating area )    12个(12 sets)

 --加热方式：(method of heating )  

 --高温段     不锈钢陶瓷加热圈

--铸铝加热瓦及带式加热器(aluminum heater & belt heater )

 --冷却方式：(method of cooling)    内外水循环冷却，带自动旁路系统外冷却( cycle water ,cooling with auto side-road system)

D.发泡剂注入单元 (foamer injection unit )     1套 (1 set)

    --发泡剂种类：(sort of foamer)  液化丁烷 (butante in liquid state )

    --泵种类：(sort of pump)     高压计量泵 (high pressure measure pump)

    --输出压力：(output  pressure )   ***300巴 (highest : 300Pa)

    --输出量调节：(output regulation)  调节活塞行程(regulate the itinerary of piston)

    --压力表：(pressure panel )     0---500兆巴 0-500MPa

     --行程控制：(process control )  刻度手轮 graduational hand wheel

     --泵驱动马达：(driving motor by pump)     2HP ×4P×1套

E.抗缩剂注入单元 (anti- contractor injection unit)         1

  --搞缩剂种类：(sort of anti-cintroutor) M-1，硬脂酸单甘酯(hard fatly

 acid single glycerine)

  --计量泵型式：sort of pump   高压计量泵，单缸柱塞式 (high pressure measure pump, pillarw piston

    --计量范围：( the range of measure ment )   20L/127次

    --压力表：(pressure panel)       0--300巴，1个 0-300Pa 1 set

    --熔化锅体积：(volume of melting-pot      5-7 L

    --泵驱动马达：(driving motor by pump)          0.75KW×4P

F.发泡机头单元(foaming mold head unit)  

    --材质：(material )        45钢粹火调质 

    --加热方式： heating method 带式加热器 belt heater

    --熔体压力表：fuse pressure panel   0~30MPa

 --熔体温度：(fuse temperature )  T/M探测器，1个探测点 T/M dete ctor, 1 detecting site .

G.自动换网装置系统(auto replacing net device system.)

      a)自动换网圈两个，网板调质氮化处理；

      b)液压电磁式左右推进，网圈固定于网板上，加热区为2区。

H.风环和定型鼓单元(air ring & mold drum unit.)

     --风环 (air ring)

      a) 材质: (meterial )  铸铝 forged aluminum ￠650mm

      b)  吹气方式: (blowing method)   风机  air engine

      c)  风机马达: (air motor)      1/2HP

     --定型鼓( mold drum ) 按合同

 a)  材质: (material )   钢

 b)  冷却方法: (cooling method )  水冷+风冷  (cooling water +cooling wind)

c)  剖开方法:(methods for cutting open)  电动圆刀

d)  定型鼓尺寸: (size of mold drum ) （按合同）

e)  风机: (air engine )          1/2HP

I.展平单元 (expanding unit)    1套 1set

      --碳钢架，逐步展开式 (carbon steel & stainless steel rack gradually expand)

      --材质：(material )        钢 SS41+SUS

     --展开座             5套

    --展开架              10个

J.牵引单元 (haul-off unit)   1套  1set

      --卷辊尺寸：(size of expanding roller )     ∮420×1750×2套

      --材质：(material)   钢辊静电胶带处理   

     --传动马达（可调速）：(driving motor )   3HP×4P

      --展开辊尺寸：(size of expanding roller)          ∮135×1750长

 --展开辊材质： (material of expanding roller)  钢丝展平辊

K.卷取单元 (rolling unit )      1套 (1 set )

      --型式： (model ) 双轴悬臂转位式

     --   --双工位自动卷取

     --收卷杆长度1750mm

    --牵引、卷取部份控制柜 parts of haul & rolling control equipment

   --***卷取重量：(maximum of rolling weight)  ***40公斤×1米直径 (maximum 40kg×1m diameter

      --张力：(tension)   15公斤/米 (15kg/m)

      --传动马达（可调速）：(driving motor  regulatire)   转矩马达50KG/CM2×2台 (revolving motor 50kg/cm2×2 set

      --长度控制：length control  可预设长度及可报警的计长控制器

      --转位驱动马达：revolving driving motor  1HP×1/10齿轮减速马达(1HP×1/10 gear dece leration motor

L.成核剂加入单元及粉料拌料单元 adding rucleonizer、banliao unit 1套1 set

    --喂料能力： feeding capacity   每分钟2-30克 2-30g/m

    --喂料方式： feeding method   螺旋连续喂料 Rotatively and constantly feeding materials  

   --传动马达： driving motor       VS0.4KW