OG-200EPE生产设备报价单

OG-200EPE生产设备报价单

一、价目表  price chart

报价：万元（FOB重庆）

型号：OG-EPE200     model:  OG-EPE200

二、目录  (content)

1、主要设备清单(List of major  equipments)

2、主要设计数据(Data of  main design)

3、公用工程要求(Demands of public project)

4、各单机规格(specifications  of each part)

5、备件清单(List of spare parts)

1.主要设备清单(List of maior equipments)

A.钢结构架  (steel  rack structure)                     1套  (1set)

B.自动加料单元(auto  feeding unit)                     1套  (1set)

C.挤出单元  (squeezing unit )                          1套 (1set)

D.发泡剂注入单元  (foamer-injecting  unit)              1套 (1set)

E.抗缩剂注入单元 (anti-contractor-injecting unit )          1套 (1set)

F.发泡模头单元 (foaming mold-head unit )               1套 (1set)

G.自动换网装置系统(auto replacing net device system)      1套(1set)

H.风环和定型鼓单元 (air ring & molding drum unit )       1套 (1set)

I.冷却展平单元 (expanding unit )                       1套(1set)

J.牵引冷却单元 (haul-off  unit )                       1套(1set)

K.卷取单元 (rolling   unit )                          1套(1set)

L.自动控制单元  (auto control unit )                     1套(1set)

M.成核剂注入单元单元（adding rucleonizer, powder material mixing unit

1套(1set)

N. 冷却水加温控制器元(static electricity  eliminator)      1套(1set)

K.备品备件单元                                      1批

2.主要设计数据 (major design  data)

*  应用树脂: (resin applied )              LDPE

*  挤出机能力:   (capacity of squeezing engine)

   大约500--650KG/HR (about  500-650kg/hr)

   (生产10毫米以下片材时产量相对较低)(yield would be relatively low when  producing  10mm )

*  片材厚度:  (thickness of sheet) 3.5~18mm(about 3.5-18mm)

*  片材密度   15KG-35KG/每立方米

*  片材宽度: 片材宽度在1000-1650MM之间可调，生产厚度8MM-18MM产品时宽度在1000MM-1650MM左右。

*  生产线速度: (speed of manufacture line)          10--80M/MIN

*  电源规格:     3相X380V×50HZ    specifications  of power  :three phrases

3.公用工程要求( Demands of Public Project )

*   电功率: (electric power)  约290KW(about290kw)  

(三相电机变频器)

*   冷却水: (cooling water )  600升/时 (600L/Hr)

*   丁烷泵: (butane gas)      250L/三泵头 ( 250L/min)

*   M-1抗缩剂注入             28L/双泵头(28L/MIN)

4.各单元规格(specifications of each   single part)

A.  钢结构架 (steel rack structure )              1套  (1set)

a) 配料操作台: SS45钢制

operation table of blending materials :ss41 made of steel

     b)   钢扶梯:    SS45钢制  

steel ladder : ss45 made of  steel

B.自动加料单元 (auto  feeding unit )         1套  ( 1 set)

a)  能力:     (capacity ) 单吸           1000公斤/小时(1000kg/hr)

  b) 加料方式:  (feeding method )          自动吸料( auto feed)

c)  料斗:    (measure implement)         不锈钢圆锥型(conical shape)

C.挤出单元 (squeezing unit)              1套( 1  set)

 a)减速箱(deceleration box)

   型式：(model   )                硬面齿420 (helical gear without pole)

材质：(material )        FCD25（可锻铸铁）(forgeable lion)

箱体：(box body)        FC20       型号420

   齿轮：(gear wheel)SCM4（特殊齿形磨光和加热处理）                                 special gear wheel bolishing and heating  dealing

   马达：  (motor )         AC220KW    配220KW变频器

   b)颈部  (neck )

     型式：(model)                     水冷夹套(  cooling water set)

     材质：(material )      FCD25     （可锻铸铁）( able to forge steel)

   c)螺筒 (spiral tube )

直径：(diameter )               ∮200×290mm

     材质：(material)        38铬目合金钢,经氮化处理HRC55-58nitrogenized and chromium-plated

压缩比：(compression ratio)            3.5：1

      转速：(notating  speed )            0-48转/分   0-48  turn /m

     加热区：(heating area )                 12个(12 sets)

    --高温段          不锈钢陶瓷加热圈

    --低温段铸铝加热器  

冷却方式：(method of cooling)       内外水循环冷却

D.发泡剂注入单元、自动调节加量 (foamer injection unit )         1套 (1 set)

发泡剂种类：(sort of foamer)  

液化丁烷 (butante in liquid state )

泵种类：(sort of pump)                 高压计量双泵头 (high pressure measure pump)

输出压力：(output   pressure )           ***300帕 (highest : 300Pa)

输出量调节：(output  regulation)         调节活塞行程(regulate the itinerary of piston)

压力表：(pressure panel )                0---300帕  0-300Pa

行程控制：(process control )             刻度手轮  graduational hand wheel)

泵驱动马达：(driving motor by pump)      2HP ×4P×1套

E. 抗缩剂注入单元、自动调节加量 (anti- contractor injection unit)   双头    1套

 抗缩剂种类：(sort of anti-cintroutor) M-1，硬脂酸单甘酯(hard fatly acid single glycerine)

计量范围：( the range of measurement  )      35--245CC/min

压力表：(pressure panel)           0--300帕，1个  0-300Pa  1  set

熔化锅体积：(volume of melting-pot           15-20 L

泵驱动马达：(driving motor by pump)            0.75KW×4P

F.发泡机头单元(foaming mold head unit)                         

材质：(material )                     45钢铸造调直

加热方式： heating method             带式加热器  belt heater

熔体压力表：fuse pressure panel       0~30MPa

厚度控制：(thickness control)          自动调节

(regulate by the spead of spiral stick and the distance between mold heads

材质：material                      热处理的特殊钢(special steel for heating control)

加热方式：(method of heating )         带式加热器 (belt heater)

加热段：(heating region)               4区        4region

熔体压力表：(fuse pressure panel )     0~30Mpa

熔体温度：(fuse temperature )          T/M探测器，1个探测点

T/M detector, 1 detecting site

G.自动换网装置系统(auto replacing net device system.)

液压电磁式左右推进，网圈固定于网板上，加热区为2区。

H.风环和定型鼓单元(air ring & mold drum unit.)

风环  (air ring)

a)材质:  (material )                  铸铝forged aluminum  φ650mm风环

b)吹气方式: (blowing  method)         风机   air engine

c)风机马达:  (air motor)              1/2HP

定型鼓( mold drum )

a)材质:  (material )                  不锈材质

b)冷却方法: (cooling method )        风冷   (cooling wind)

c)剖开方法:(methods for cutting open)   电动圆刀

d)定型鼓尺寸:  (size of mold drum )  按合同

e)风机: (air engine )                  1/2HP     2台

I.展平单元部分 (expanding unit)       

钢架，逐步展开式。 (carbon steel & stainless steel rack gradually expand)

展开座部分                        5套

展开架部分                        10个

材质：(material)                     45钢

   冷却方式                            风冷

J,牵引单元部分                    1套  

牵引辊尺寸：(size of expanding roller )          ∮420×1750×2支

材质：(material)                           45钢 防静电胶带

传动马达（可变频调速）：(driving motor )      3HP×4P

过辊尺寸：(size of expanding roller)    ∮160×1750MM

展开辊材质： (material of expanding roller)      ∮130×1750MM 螺纹反向

K、卷取单元 (rolling unit )           1套  (1 set )

型式： (model )  双轴悬臂翻转式  

***卷取重量：(maximum of rolling weight)    ***40公斤×1米直径

                                    maximum 40kg×1m  diameter

张力：(tension)                    30公斤/米  (30kg/m)

传动马达（可调速）：(driving motor   regulative) 转矩马达50KG/CM2×2台

revolving motor 50kg/cm2×2 set

长度控制：length control          可预设长度及可报警的计长控制器

转位驱动马达：revolving driving motor    1HP×1/10齿轮减速马达

1HP×1/10 gear dece leration motor

L.自动控制单元   (auto control unit)1套  1 set

a)温度控制：temperature control

挤出机：squeezing engine        12个区     12  regions

模头：mold head                 4个区      4  regions

b)传动马达控制 driving motor control

挤出机AC马达控制柜squeezing engine AC motor control cabinet

牵引、卷取部份控制柜 parts of haul & rolling control equipment

M.成核剂加入单元及粉料拌料单元adding rucleonizer, powder material mixing unit 1套  1set

喂料能力： feeding capacity       每分钟2-30克 2-30g/m

喂料方式： feeding method      螺旋连续喂料

Relatively and constantly feeding materials

传动马达： driving motor              VS0.4KW